How to measure fret size: crown width and crown height on a fret

How to Measure Fret Size With a Caliper (and Identify Your Fret Wire)

If you are planning a refret, buying a used neck or just curious why one guitar bends easier than another, the first step is knowing what frets are on it now. You need a digital caliper and about two minutes. Here is how to measure crown width and height accurately, and how to turn those numbers into a fret size.

Already have your numbers? Enter them into the Identifier in the free Mbit Fret Guide, in inches or mm, and it matches them against its fret wire database within ±0.006″.

What You Need

A digital caliper that reads to 0.01 mm or 0.001″. An inexpensive one is fine for this. Clean, dry frets, and ideally a fret that does not see much play, since worn frets read low.

Step 1: Pick the Right Fret

Measure a high fret, somewhere past the 15th. Most playing happens on the first seven frets, so those are worn the most. A barely touched upper fret is closest to the original wire.

Step 2: Measure Crown Width

Close the outside jaws gently across the fret, measuring along the length of the neck, where the fret meets the fingerboard. Do not squeeze. Take three readings at different spots across the fret and use the middle one.

Step 3: Measure Crown Height

Use the depth rod at the end of the caliper. Rest the end of the caliper body flat on the top of the fret, zero it, then lower the rod until it touches the fingerboard right beside the fret. The reading is the height above the board. Alternatively, measure fret top to board with the jaws held square, but the depth rod is more repeatable. Either way, you are measuring above the wood: the tang hidden in the slot never counts.

Step 4: Match It to a Size

If you measure about You likely have Profile
.080″ × .043″ (2.03 × 1.09 mm) Dunlop 6230 / Jescar 43080 Vintage small
.084″ × .040″ (2.13 × 1.02 mm) Dunlop 6190 Vintage small
.102″ × .042″ (2.59 × 1.07 mm) Dunlop 6150 Vintage jumbo
.106″ × .036″ (2.69 × 0.91 mm) Dunlop 6130 Wide and low
.104″ × .047″ (2.64 × 1.19 mm) Jescar 47104 Medium jumbo
.090″ × .055″ (2.29 × 1.40 mm) Dunlop 6105 / Jescar 55090 Narrow tall
.110″ × .055″ (2.79 × 1.40 mm) Dunlop 6100 / Jescar 57110 Jumbo
.118″ × .058″ (3.00 × 1.47 mm) Dunlop 6000 / Jescar 58118 Extra jumbo

Why Your Numbers Might Not Match Exactly

Factory frets are leveled and crowned after install, which lowers height and can narrow the crown slightly. A guitar that has had a fret dress since may read .005″ or more under its original spec. Width survives better than height, so trust width first when two sizes are close. And some factories use their own wire that does not match any aftermarket number. If nothing lines up, that is the likely reason, not a measuring mistake.

Frequently Asked Questions

How do I know what size frets are on my guitar?

Measure crown width and height on an upper fret with a digital caliper, then compare against a fret size chart. The manufacturer's spec sheet for your model is also worth checking.

Should I measure width at the top or the base of the fret?

At the base, where the crown meets the fingerboard. That is how fret wire is specified.

Does the tang count in fret height?

No. Fret height is measured above the fingerboard only. The tang sits inside the slot.

My frets measure low. Do they need replacing?

Not necessarily. Low height alone is fine if the guitar plays clean. Deep grooves, buzzing that a setup cannot fix or frets too low to level again are the signs to talk to a luthier about a refret.

More Fret Wire Guides

Fret size chart · Fret sizes explained · 6105 vs 6100 · Stainless vs nickel · Tall frets and sharp chords

Or answer five questions in the free Mbit Fret Guide and it ranks 28 verified fret wire specs against how you actually play.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.